Welcome to Autotec Vehicle Technology Solutions ,  Sign-in or  Create an Account
  • Greenstone: +27 (11) 452-9059
  • Waterfall: +27 (10) 006-0317
Welcome to Autotec Vehicle Technology Solutions

Kicker Marine 44KXMA8008 8ch Amplifier

Kicker Amplifier
R 0.00
Availability:  
  • Powerful, dependable, and good-looking Kicker's KXMA800.8 marine 8-channel amplifier will bring brilliance and clarity to your sound, powering eight speakers with 50 watts RMS each. You can also use this amp in a 4-way system, with two channels powering tweeters, two channels powering midrange drivers, two powering mid-bass speakers, and two channels bridged together to power a subwoofer with up to 200 watts RMS. This versatile amp will always find a place in your boat's sound system, no matter how it evolves over the years. Stays cool under pressure This reliable and compact KXM Series rocker will run cool even when pushed hard, thanks to its high-mass heatsink, high-tech internal components, and efficient full-range Class-D amp technology. Made for marine use The KXMA800.8 features a conformal-coated circuit board for improved water and dust resistance, plus corrosion-resistant power connections, a gasket-sealed front cover, and stainless steel mounting hardware that won't rust all over your boat's gel coat or carpeting. Connection perfection Kicker employs their Fail-Safe Integration Technology (FIT2™) to reject noise and stop any interference generated by your boat's electronics, so you'll enjoy your music clean and pure. Speaker-level inputs make it possible to hook this amp up to almost any stereo receiver or radio. Kicker also helps you set this amp's gain properly, by offering free test tones for downloading. You play a tone and turn the gain up until the gain knob glows red. Then, you turn it down until it just goes out, and the amp's gain is set perfectly. Versatile controls behind the folding door A gasket-sealed front door gives you quick and easy access to your amp's controls. You can tune for almost any kind of speaker, as the steeply-sloped high- and low-pass filters offer a wide range of adjustment. The filter sections for the Amp 3 and Amp 4 channels can be set up for bandpass operation — where both the high- and low-pass filters are engaged to allow only the frequencies between them to play — for optimizing the signal for midrange speakers in a 3- or 4-way system.

RMS Power [Watts]:
@ 14.4V, 4ohm stereo, = 1% THD+N: 50 x 8
@ 14.4V, 2ohm stereo, = 1% THD+N: 100 x 8
@ 14.4V, 4ohm bridged mono, = 1% THD+N: 200 x 4
Length [in, cm]:
14-¾, 37.4
Height [in, cm]:
2-?, 5.5:
Width [in, cm]:
8-5/16 , 21
Frequency Response [Hz]:
10Hz–20kHz
Signal-to-Noise Ratio [dB]:
95
Input Sensitivity:
250mV–10V
Selectable Electronic Crossover:
Amp 1 and Amp 2: OFF/HP/LP
Variable 10–5,000Hz with X10 switch:
Amp 3 and Amp 4: OFF/HP/LP/BP
Variable HP, 10–500Hz
Variable LP, 40–5,000Hz with 10X switch
Slope: 24dB/octave
KickEQ+™ Bass Boost:
0-18dB @ 40Hz
CEA Power:
50 x 8 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006B (Watts)
CEA Signal-to-Noise Ratio
-75dB CEA-2006B (ref: 1W, A-weighted)